Author Topic: SLAYER? I KNOW!  (Read 341 times)

cpt_sfc

  • Full Member
  • ***
  • Posts: 177
SLAYER? I KNOW!
« on: April 06, 2021, 05:59:19 PM »
MY slayer is leaking again and as no one to send it to!. Looking for thoughts/help.
thanks



steveoh

  • Administrator
  • Hero Member
  • *****
  • Posts: 2876
    • Airgun FPE Calculator
Re: SLAYER? I KNOW!
« Reply #1 on: April 06, 2021, 07:09:04 PM »
That’s a crying shame. I’m sure someone here can help you. Bob or Motörhead are good candidates.
  • Benicia, California
Quackenbush .58 Outlaw
Shooting Chairs
Vallejo Ferry Schedule
DAQ .458 LA Outlaw Rifle
Sam Yang 909s .45
Sam Yang Sumatra .25
RWS Diana 350Magnum Compact Pro .22
QB-79 .177
Crosman 1322
Crosman 1377 - HoRodded 10 FPE
Diana Model 27 (childhood airgun)
Tolman Skiff
Airgun Calculator

Alan

  • Administrator
  • Hero Member
  • *****
  • Posts: 3801
  • Set the example... Don't be one!
    • Mobile Amateur Radio
Re: SLAYER? I KNOW!
« Reply #2 on: April 07, 2021, 05:57:14 AM »
I may be in the dark, but as far as I know, they're still in business. Have you tried to contact them?
  • Roswell, New Mexico
Alan

I have a Hill EC-3000 compressor. If you're a fellow Guild member, and you pass through Roswell, NM, I'll fill your tank as a courtesy (4,250 PSI limit).

steveoh

  • Administrator
  • Hero Member
  • *****
  • Posts: 2876
    • Airgun FPE Calculator
Re: SLAYER? I KNOW!
« Reply #3 on: April 07, 2021, 07:22:44 AM »
I may be in the dark, but as far as I know, they're still in business. Have you tried to contact them?

From what I've read over the past year or two, the owner is not responsive to calls or email, and has taken money for airguns but not delivered. So it goes in the bleeding edge, under funded nature of airgun manufacturing.
  • Benicia, California
Quackenbush .58 Outlaw
Shooting Chairs
Vallejo Ferry Schedule
DAQ .458 LA Outlaw Rifle
Sam Yang 909s .45
Sam Yang Sumatra .25
RWS Diana 350Magnum Compact Pro .22
QB-79 .177
Crosman 1322
Crosman 1377 - HoRodded 10 FPE
Diana Model 27 (childhood airgun)
Tolman Skiff
Airgun Calculator

cpt_sfc

  • Full Member
  • ***
  • Posts: 177
Re: SLAYER? I KNOW!
« Reply #4 on: April 07, 2021, 07:42:47 AM »
I sent an e mail to Airarms. I hope he answers. Last time and time before that it took months to get it back. If he has a kit and valve assm and maybe a movie on how to take it apart! I guess I'd try to rebuild it myself. This is the 3rd time I think it has happened. I sprayed all over looking for bubbles nada. I think it my be the valve? don't know . Thanks for the info as the last time I tried to make contact , no luck at all. I thought he stopped making them? Sold off parts? oh well getting senile.

Alan

  • Administrator
  • Hero Member
  • *****
  • Posts: 3801
  • Set the example... Don't be one!
    • Mobile Amateur Radio
Re: SLAYER? I KNOW!
« Reply #5 on: April 07, 2021, 08:18:32 AM »
I've done some more research....

I wish there was a black list of sorts, because this is another potential member.
  • Roswell, New Mexico
Alan

I have a Hill EC-3000 compressor. If you're a fellow Guild member, and you pass through Roswell, NM, I'll fill your tank as a courtesy (4,250 PSI limit).

cpt_sfc

  • Full Member
  • ***
  • Posts: 177
Re: SLAYER? I KNOW!
« Reply #6 on: April 07, 2021, 08:38:42 AM »
Thanks for the info. One would think that the makers would have a rebuild kit on hand for the future. It sucks when you grab it, head out to the barn take aim at a coyote , pull the trigger and pffft. The 38 cal round ball went about 10 feet. If I would have had a 127 gr HP cast it would not even have come out of the tube. The dam thing is even too big for a paper weight. The only other airguns I have o rings go out of are 2 same yangs that I have had for years.

cpt_sfc

  • Full Member
  • ***
  • Posts: 177
Re: SLAYER? I KNOW!
« Reply #7 on: April 07, 2021, 08:44:09 AM »
I now have a rubber glove sealed over muzzle , lets see if air blows it up? will let you know.

Tinkerer

  • Full Member
  • ***
  • Posts: 119
Re: SLAYER? I KNOW!
« Reply #8 on: April 07, 2021, 11:41:27 AM »
Airguns of Arizona is his dealer.  Might they be of help?
Glen

cpt_sfc

  • Full Member
  • ***
  • Posts: 177
Re: SLAYER? I KNOW!
« Reply #9 on: April 07, 2021, 12:51:54 PM »
AOA , I called and they where closed for training no open date. No slayer listed in search engine on their site.  Is it TOM that ran it. Did he have any fix it u tubes? So far no air in rubber glove.

Tinkerer

  • Full Member
  • ***
  • Posts: 119
Re: SLAYER? I KNOW!
« Reply #10 on: April 07, 2021, 06:25:50 PM »
American Air Arms site does show this:
https://americanairarms.com/product/slayer-o-ring-kit/
But its out of stock!
And they do have technical drawings too.
Glen

cpt_sfc

  • Full Member
  • ***
  • Posts: 177
Re: SLAYER? I KNOW!
« Reply #11 on: April 08, 2021, 10:06:57 AM »
OK got the info. not all would print, but the o ring list and air tube and valve did.  It is kinda scary when you look at the schmatics.
thank you for the help.
If I fubar it I'll send it to motor head LOL, but really!
thanks
max

cpt_sfc

  • Full Member
  • ***
  • Posts: 177
Re: SLAYER? I KNOW!
« Reply #12 on: April 27, 2021, 02:38:00 PM »
Send slayer to Allen Z in ID. This week Says he has fixed a lot of them.