American Air Arms

predator-pellets

Neil Clague Air Strippers, Shrouds and LDCs

windmeister-ad

Wicked Air Rifles - Flex

Marmot Militia Machine Works

Author Topic: Raptor Pneumatics  (Read 301 times)

Alan

  • Hero Member
  • *****
  • Posts: 1249
  • Set the example... Don't be one!
    • View Profile
    • Mobile Amateur Radio
Raptor Pneumatics
« on: June 15, 2017, 02:45:47 PM »
Does anyone have a phone number for Raptor Pneumatics? I have an email address, but no answer. AoA is the dealer, but their service department hasn't returned either of my two calls.


  • Roswell, New Mexico
Alan

I have an Omega compressor. If you're a fellow Guild member, and you pass through Roswell, NM, I'll fill your portable tank as a courtesy.

bnowlin

  • Sr. Member
  • ****
  • Posts: 375
  • Just a Plain Ole Country Boy
    • View Profile
Re: Raptor Pneumatics
« Reply #1 on: June 15, 2017, 03:17:45 PM »
Does anyone have a phone number for Raptor Pneumatics? I have an email address, but no answer. AoA is the dealer, but their service department hasn't returned either of my two calls.

Try Todd Brown 704 252 3024
Bob

Alan

  • Hero Member
  • *****
  • Posts: 1249
  • Set the example... Don't be one!
    • View Profile
    • Mobile Amateur Radio
Re: Raptor Pneumatics
« Reply #2 on: June 15, 2017, 04:03:05 PM »
I will give that a try. It is past 7 pm there as I write this, so I'll try in the morning.
  • Roswell, New Mexico
Alan

I have an Omega compressor. If you're a fellow Guild member, and you pass through Roswell, NM, I'll fill your portable tank as a courtesy.

bnowlin

  • Sr. Member
  • ****
  • Posts: 375
  • Just a Plain Ole Country Boy
    • View Profile
Re: Raptor Pneumatics
« Reply #3 on: June 15, 2017, 04:15:45 PM »
Alan he has a speech problem so bear with him.  That's his cell but he is in  in Arizona.
Bob

Alan

  • Hero Member
  • *****
  • Posts: 1249
  • Set the example... Don't be one!
    • View Profile
    • Mobile Amateur Radio
Re: Raptor Pneumatics
« Reply #4 on: June 15, 2017, 04:27:11 PM »
Thank you.

That worked! Thank you over again!

I owe you one Bob!
« Last Edit: June 15, 2017, 04:33:09 PM by Alan »
  • Roswell, New Mexico
Alan

I have an Omega compressor. If you're a fellow Guild member, and you pass through Roswell, NM, I'll fill your portable tank as a courtesy.

bnowlin

  • Sr. Member
  • ****
  • Posts: 375
  • Just a Plain Ole Country Boy
    • View Profile
Re: Raptor Pneumatics
« Reply #5 on: June 15, 2017, 05:18:29 PM »
Alan what'  wrong with it.
Bob

Alan

  • Hero Member
  • *****
  • Posts: 1249
  • Set the example... Don't be one!
    • View Profile
    • Mobile Amateur Radio
Re: Raptor Pneumatics
« Reply #6 on: June 15, 2017, 05:28:33 PM »
The bleed valve started leaking in two places; the main body, and the screw itself. Although it may have been leaking for some time.

I had two nylon washers, 1/2 inch by 1/32, and two of them with some silicon grease took care of the main body. The seal at the end of the screw was leaking too, and there is a replacement in the parts bag. Todd has them in stock if I need another, but a tad of silicon grease got it to seal back up without replacing it.

The assembly is kind of rare because of the thread size, but he does have the later version. So if it starts leaking again, I'll just replace the whole assembly.

Again, I appreciate the name and number. By the way, AoA finally called me back with the same information on Todd.
  • Roswell, New Mexico
Alan

I have an Omega compressor. If you're a fellow Guild member, and you pass through Roswell, NM, I'll fill your portable tank as a courtesy.

bnowlin

  • Sr. Member
  • ****
  • Posts: 375
  • Just a Plain Ole Country Boy
    • View Profile
Re: Raptor Pneumatics
« Reply #7 on: June 15, 2017, 06:05:37 PM »
Yea he is a very nice guy I have talked to him several times.  In fact I sent my whole cylinder in and he re built it for nothing.
Bob