Author Topic: NOE Announces More Pellet Moulds  (Read 1815 times)

rsterne

  • Member 2000+fps Club
  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1587
  • Mozey-On-Inn and see what Coalmont has to offer!
    • Mozey-On-Inn
Re: NOE Announces More Pellet Moulds
« Reply #15 on: November 26, 2018, 04:33:11 PM »
If I scaled up the .30 cal Hunter to 0.575 cal, it would be 320-360 gr. and be 0.69" long.... Either one should work just fine, it's a matter of drawing up the one you guys want.... I also need to know the head and skirt diameter you want.... The head diameter should be close to, but NOT over, the groove diameter of the barrels.... but MUST be larger than the land diameter.... The skirt diameter would normally be about 0.012" larger than the head, to keep the proportions used in JSB (and NOE) pellets of other calibers.... Part of the large difference between head and skirt diameters is to make the pellet forgiving, so that they are tolerant of barrel dimension variations between manufacturers.... If there is only ONE set of barrel dimensions, the skirt and head can be closer to the same dimensions.... It is usual for the skirt to collapse slightly when loaded into the chamber....

Bob
« Last Edit: November 26, 2018, 04:36:03 PM by rsterne »
  • Coalmont, BC

steveoh

  • Administrator
  • Hero Member
  • *****
  • Posts: 1139
    • Airgun FPE Calculator
Re: NOE Announces More Pellet Moulds
« Reply #16 on: November 26, 2018, 04:38:28 PM »
If I scaled up the .30 cal Hunter to 0.575 cal, it would be 320-360 gr. and be 0.69" long.... Either one should work just fine, it's a matter of drawing up the one you guys want.... I also need to know the head and skirt diameter you want.... The head diameter should be close to, but NOT over, the groove diameter of the barrels.... but MUST be larger than the land diameter.... The skirt diameter would normally be about 0.012" larger than the head, to keep the proportions used in JSB (and NOE) pellets of other calibers.... Part of the large difference between head and skirt diameters is to make the pellet forgiving, so that they are tolerant of barrel dimension variations between manufacturers.... If there is only ONE set of barrel dimensions, the skirt and head can be closer to the same dimensions.... It is usual for the skirt to collapse slightly when loaded into the chamber....

Bob

As soon as I can find my bloody calipers I'll measure.  Three new kittens have knocked stuff on the floor and batted those things around. I can't find squat.  :o >:(
  • Benicia, California
Quackenbush .58 Outlaw
Shooting Chairs
Vallejo Ferry Schedule
Sam Yang 909s .45
Sam Yang Sumatra .25
RWS Diana 350Magnum Compact Pro .22
QB-79 .177
Crosman 1322
Crosman 1377 - HoRodded 10 FPE
Diana Model 27 (childhood airgun)
Tolman Skiff
Airgun Giveaway

Bullfrog

  • Administrator
  • Full Member
  • *****
  • Posts: 166
Re: NOE Announces More Pellet Moulds
« Reply #17 on: November 27, 2018, 01:02:25 PM »
Are these still in the works? I’m very interested in the .45 pellet. Heck I’m interested in all of them. But especially the .45. My .308 Texan SS and .300 Flexes love the .30 Hunter. I got a hunch my .45 Texan will similarly love the .45 Hunter.

tkerrigan

  • Full Member
  • ***
  • Posts: 110
Re: NOE Announces More Pellet Moulds
« Reply #18 on: November 27, 2018, 01:25:02 PM »
I went out and measured the DAQ .575 barrel on my pistol.  I used an old (before cheap) Mitutoyo dial caliper that is accurate.  The bore was right at .575 several times, the lands were .569 using two precision pins that fit when together, a .284 and a .285.  Remember I want one.  Regards, Tom
  • Jefferson, OR

KralPB25

  • Newbie
  • *
  • Posts: 1
Re: NOE Announces More Pellet Moulds
« Reply #19 on: December 02, 2018, 09:41:22 AM »
Is there a way to order a sample pack of the .251 pellets and slugs? I have a .25 Krsl puncher breaker, tuned by Troy Hammer that does great with the JSB Mark 2 and pretty decent accuracy wise with the grizzly slugs. 

The Grizzly slugs have been extremely hard hitting on Jack Rabbits/coyotes as well as getting 40-50 shots before any significant POI drop. The JSBs are more noticable once it gets past 30 shots on the point of impact drop.

Anyone else have a recommendation of what NOE bullet styles work best in their Krals?
  • Dallas, TX

rsterne

  • Member 2000+fps Club
  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1587
  • Mozey-On-Inn and see what Coalmont has to offer!
    • Mozey-On-Inn
Re: NOE Announces More Pellet Moulds
« Reply #20 on: December 06, 2018, 05:15:53 PM »
The NOE .30 cal Hunter pellet moulds are now in the store.... 46-51 gr.... http://noebulletmolds.com/NV/index.php?cPath=30_585

Last day today, Dec. 7,  for 20% Discount.... use Code c51c9f55 ….

Bob
« Last Edit: December 07, 2018, 07:50:00 AM by rsterne »
  • Coalmont, BC

rsterne

  • Member 2000+fps Club
  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1587
  • Mozey-On-Inn and see what Coalmont has to offer!
    • Mozey-On-Inn
Re: NOE Announces More Pellet Moulds
« Reply #21 on: December 13, 2018, 05:56:23 PM »
The NOE .35 cal Magnum Hunter pellet moulds are now in the store.... 84-95 gr.... http://noebulletmolds.com/NV/index.php?cPath=35_586

Bob
  • Coalmont, BC

steveoh

  • Administrator
  • Hero Member
  • *****
  • Posts: 1139
    • Airgun FPE Calculator
Re: NOE Announces More Pellet Moulds
« Reply #22 on: December 13, 2018, 07:41:43 PM »
I went out and measured the DAQ .575 barrel on my pistol.  I used an old (before cheap) Mitutoyo dial caliper that is accurate.  The bore was right at .575 several times, the lands were .569 using two precision pins that fit when together, a .284 and a .285.  Remember I want one.  Regards, Tom

My Accurate 58-315s, .58 (EPP-UG Clone) bullet mold was waiting for me today when I got home from work! That is mighty fast!
« Last Edit: December 14, 2018, 09:31:34 AM by steveoh »
  • Benicia, California
Quackenbush .58 Outlaw
Shooting Chairs
Vallejo Ferry Schedule
Sam Yang 909s .45
Sam Yang Sumatra .25
RWS Diana 350Magnum Compact Pro .22
QB-79 .177
Crosman 1322
Crosman 1377 - HoRodded 10 FPE
Diana Model 27 (childhood airgun)
Tolman Skiff
Airgun Giveaway

Bullfrog

  • Administrator
  • Full Member
  • *****
  • Posts: 166
Re: NOE Announces More Pellet Moulds
« Reply #23 on: December 13, 2018, 10:09:38 PM »
I got my .30 46 mold in day before yesterday and cast a tin tonight. Mine are coming out at 45 grains. They look great. Hopefully my short Flex likes them.

Now about those .45 pellets... I'm jumping all over that mold when it comes out.