Author Topic: Jkhan noblesse .22 and 30g bbt  (Read 933 times)

oneshot61

  • Full Member
  • ***
  • Posts: 115
Jkhan noblesse .22 and 30g bbt
« on: February 09, 2017, 04:53:03 PM »
Had a chance to sneak in a few rounds today with my jkhan noblesse .22. I had previously shot the 30g bbt sized at 217 nose and 219 rear drive band. Ok accuracy to 50 yards but I felt they could definitely do better. I ordered some sizing dies from noe for my .25 and one for the .22 in 216.. sounds a bit small I know. The lothar walther is 215 lands 221 groves... but is also chocked. So I sized down a few and ran down to the range. Definitely tighter groups, on par with my shooting the 18 jsb... with the open reticle, not a scope.
 The picture below is 5 shots, three in the same hole...winds, nnw @ 11 mph with higher gusts, open reticle. When I can, I'll get a .217 sizing die and try that also, but I must say I am very encouraged with the new results. That group is a bit less than the size of  a dime.



maddoghutty

  • Newbie
  • *
  • Posts: 9
Re: Jkhan noblesse .22 and 30g bbt
« Reply #1 on: December 09, 2017, 05:56:15 PM »
Hi oneshot I also have the Noblesse. 22 and have been also looking to buy a mould so I too can mould my own pellets. But been from the UK and never done this before could you tell me what mould to buy to create the same pellets you have created. I think that target you shot in a 9mph wind was great 3 in the same hole spot on. Like I said I have never looked at custom pellets before so if you have found a better one than what you already did here I would like to hear about it. Also if you would tell me what to order to make the same rounds. So please pm me or msg thx.
  • Kingston upon Hull, England

oneshot61

  • Full Member
  • ***
  • Posts: 115
Re: Jkhan noblesse .22 and 30g bbt
« Reply #2 on: January 14, 2018, 09:22:32 PM »
Pm sent 😀

Aceflier

  • Jr. Member
  • **
  • Posts: 59
Re: Jkhan noblesse .22 and 30g bbt
« Reply #3 on: January 15, 2018, 09:19:00 AM »
Had a chance to sneak in a few rounds today with my jkhan noblesse .22. I had previously shot the 30g bbt sized at 217 nose and 219 rear drive band. Ok accuracy to 50 yards but I felt they could definitely do better. I ordered some sizing dies from noe for my .25 and one for the .22 in 216.. sounds a bit small I know. The lothar walther is 215 lands 221 groves... but is also chocked. So I sized down a few and ran down to the range. Definitely tighter groups, on par with my shooting the 18 jsb... with the open reticle, not a scope.
 The picture below is 5 shots, three in the same hole...winds, nnw @ 11 mph with higher gusts, open reticle. When I can, I'll get a .217 sizing die and try that also, but I must say I am very encouraged with the new results. That group is a bit less than the size of  a dime.

How did you size the nose diff than the bands?
  • Indiana
1377 .177
Daisy 880
Ruger Blackhawk
'72 Dan
NP XL1100
.25 Mrod 75FPE (Stock parts mods by Shorty tuned by me)
Airforce Texan .457

oneshot61

  • Full Member
  • ***
  • Posts: 115
Re: Jkhan noblesse .22 and 30g bbt
« Reply #4 on: January 15, 2018, 11:16:07 AM »
That’s how they dropped. I sized them to .216 for the choke.

rsterne

  • Member 2000+fps Club
  • Global Moderator
  • Hero Member
  • *****
  • Posts: 1575
  • Mozey-On-Inn and see what Coalmont has to offer!
    • Mozey-On-Inn
Re: Jkhan noblesse .22 and 30g bbt
« Reply #5 on: January 15, 2018, 12:38:51 PM »
Quote
How did you size the nose diff than the bands?

I don't think he did.... ? .... I designed the molds that way so that guys could try a bullet where the nose fit the lands and the rear band fit the chamber / grooves.... I don't think it was necessary, just gave another option.... that goes away when you size them....

Bob
  • Coalmont, BC

Aceflier

  • Jr. Member
  • **
  • Posts: 59
Re: Jkhan noblesse .22 and 30g bbt
« Reply #6 on: January 15, 2018, 01:00:15 PM »
That makes more sense then! I couldn’t wrap my head around sizing 2 ends of a bullet lol. :P
  • Indiana
1377 .177
Daisy 880
Ruger Blackhawk
'72 Dan
NP XL1100
.25 Mrod 75FPE (Stock parts mods by Shorty tuned by me)
Airforce Texan .457